Our Drill Press Table is designed to fit virtually any drill press! With a unique post knob to T-track attachment system the table can be moved freely until you find your “comfort zone”. The table measures approximately 15” x 24” and it is laminated on both the top and the bottom to prevent any kind of warping and to keep the top flat. Approximately 1-3/8” thick, this table is built to last!

Our Deluxe Drill Press Table comes with a 32” MDF fence with mini-track pre-installed and a UHMW stop block with knob and bolt. This kit has the same unique post knob to T-track attachment system that comes standard on all of our drill press tables. The table measures approx. 15” x 24” and is laminated on both the
top and the bottom to prevent any kind of warping and to keep the top flat.

Our Supreme Drill Press Table comes with all the great features of our basic table, Plus it sets up with two - 22” Miter Fences that extends your table fence out to huge 72” wide! The two Miter Fences can be extended out or you can keep them in at the combined fence length of 44”. This package also comes with 2 UHMW stop blocks for both ends of the fence system.

The Drill Press is a great tool but has some limitations for woodworking. If you find yourself always looking for a board to place under the piece of wood you are trying to drill or a third hand to hold it in place, then this is the kit for you. This 14” X 24” deluxe drill press table kit incorporates hold down clamps, removable plate, stop block and side vertical
drilling capabilities. Everything a woodworker needs.

Have you ever needed three hands to work with long stock on your drill press, two to support the stock and one to lower the bit? Then this roller support is for you! Bolt it to any 2-1/4” to 4” drill press column and extend the outriggers, on one or both sides, up to 28” from the center of the table. The 9-3/4” work support rollers have 9” of vertical adjustment for accurate leveling. You’ll be able to position your wood across your drill press table with ease. Features a center tray to hold extra bits or tools.

No more squinting, guessing or trying to hit your center point when drilling on your drill press! The column mounted drill press laser guide is designed to give you pin point accuracy and precision for virtually any drilling operation. Two red lasers cross at the exact location the drill bit is going to contact the stock, giving you complete control of where your stock is going to be drilled. The two lasers are independent and can be adjusted for any size drill press machine. The drill press laser guide can be mounted to most any bench top or free standing drill press and it comes with a 4" steel ring clamp as well as a 6" steel ring clamp for mounting. The package also comes with a handy alignment device that fits into the chuck of the drill press to make alignment and calibration of the lasers an easy process. The unit requires a 9 volt battery which is included with the kit.

The perfect accessory for any drill press! Whether you use it as a tool storage place or as an everyday catch all you will get plenty of use out this accessory. The Drill Press Tool Tray
attaches easily to any drill press column from 1-3/4” to 3-5/8”. It has built in holes for your drill bits ranging in size from 3/32” to 1/2”.

This Drill Press Clamp adjusts quickly and easily to lock your work piece in any position. The clamping pad pivots to conform to any work piece, ensuring uniform pressure. Table top must have hole through slots in order for clamp to
work properly.

The post quickly mounts to most drill press tables or workbenches. On the drill press a bolt passes through the table and is secured with a large ring nut. Hardware is also provided to be used in 3/4" hole on your workbench to secure stock (photo above). Hold down pressure is provided by the cam action clamp on the head which features a 1-1/2" dia. rubber foot to help prevent marring your work piece.

This hard rubber pad (foot) replaces the standard pad furnished with the Quick Set Drill Press Hold Down (shown above #3339). It provides more surface area to help hold your work piece . The Quick Set Large Foot has a 1-1/2" long 5/16" stud with 16 threads per inch. The hold down pad is 2-3/8" x 1-5/8" with V-grooves for holding round stock.

The Large Quick Set Hold Foot can also be use with Large Toggle Clamps with 5/16" studs.

(Toggle Clamp Not Included)

This 75 Watt (maximum) magnetic base light holds firmly to most any machine and has three fully functional joints for
complete maneuverability and adjustability, plus a fourth joint that rotates the lamp head a full 360°. It has a 5 ft. long cord and plug. Light bulb is not included in the package.

Convenient push button release allows for quick change out of
stock. Aluminum construction. Vise opens to 2½” in width, which makes it perfect for small drill press applications.