Features and Benefits:

• For removing damaged screws fast and easy and as simple as a screwdriver

• The reusable Damage Screw Remover Kit is designed to be used in variable speed hand drill set for reverse. It can be chucked directly into the drill or held using a 1/4 inch hex bit holder

• If a hand drill is not handy, The Damage Screw Remover Kit can also be used in a hex bit screwdriver. In both applications you push down and turn.

• The Damage Screw Remover Kit removes all screws that have an indented drive fit. This includes such fasteners as Phillips, Slotted, Hex, Torx, Tri-Wing, Pozidriv, Frearson, most Tamper Resistant screws and many more.

Easy-Out Damged Screw Remover Includes:

#0 bit for 5/16" (#2-#4) screws
#1 bit for 7/64" (#6) screws
#2 bit for 9/64" (#8-#10) screws
#3 bit for 11/64" (#12) screws
#4 bit for 13/64" (#14) screws

Drill perfectly aligned hinge screwholes. Self centering, spring-loaded drill bits are guided by the hinge screw holes. Great for shelf pin drilling! The self centering bits are
equipped with hex shanks that fit all quick-change drill/drive systems.

7PC Self Centering Bit Set  Includes:

• 5/64" Self Centering Hinge Bit

• 7/64" Self Centering Hinge Bit

• 9/64" Self Centering Hinge Bit

• 11/64" Self Centering Hinge Bit

• 13/64 Self Centering Hinge Bit

• 1/4" and 5mm for Self Centering Bits for Shelf Pins

Single Self Centering Hinge Bits

Drill perfectly aligned hinge screwholes. Self centering, spring-loaded drill bits are guided by the hinge screw holes. Great for shelf pin drilling! The self centering bits are
equipped with hex shanks that fit all quick-change drill/drive systems.

Corner Mortising Chisel

This easy to use spring loaded chisel instantly squares round corners on hinge mortises. Made of hardened steel that stays sharp. Just tap lightly with a hammer for a perfectly squared corner. Ideal for use with our hinge mortising system above.

 

This 19” jig is set-up for pin spacing of 1-1/4” on center. The jig can be adjusted for drilling at either 2-1/2” or 1-15/32”
from the case edge. Indexing holes keep alignment accurate as you drill along any length board. Kit includes self-centering
1/4” brad point bit as well as the drilling jig. 5mm holes are possible as well, just by simply swapping out the
1/4” self centering bit with a 5mm self centering bit.
( 5 mm bit sold separately below).

Precisely mark position for drawer pulls with our “Drawer Pull Installation Jig”. Mark center line, choose boring width
needed and position wooden guide for correct spacing and lock. Align jig over center line & mark holes. Remove jig
and drill. Jig measures 7” wide by 6” tall. The jig is designed for the most common boring widths of 96mm, 3”, 3-3/4”,
3-1/2”, 2-1/2”, and 4”.

These single flute countersinks are machined from carbon steel and are available in 3 different diameter sizes. All have a 90° angle on the point for sharp and precise countersinking. The cutting edge is hardened and honed for sharpness. Single fluting gives the added advantage of less vibration and
chatter resulting in a smoother cut.

Use these Forstner bits for drilling hinge cup holes for cabinet doors. These bits can be used on any standard drill press
with a 3/8” chuck. These forstner bits are also great for drilling holes for fence jigs (30mm and 40mm) with magnetic
hold downs (eg. Magnetic featherboard jig). Hinge forstner bits are made with carbide tips.

Get an extra 6" of reach into deep holes with this Forstner bit extender. Great for rustic furniture, joining wide timbers, drilling pepper mills and kaleidoscopes. Use it on the wood lathe to make large deep bores for wood turning projects. Also works with any other style of 3/8" shank drill bit greater than 3/4" in diameter.

Requires a 3/4" or larger diameter hole size for use.

7-Piece Forstner Bit Set includes 7 bits:

• 1/4 "
• 3/8 "
• 1/2 "
• 5/8 "
• 3/4 "
• 7/8 "
• 1 "
• Made of high-carbon tool steel, these bits are protected in a plastic case.

7-Piece Forstner Bit Set includes 7 bits:

• 1/4 "
• 3/8 "
• 1/2 "
• 5/8 "
• 3/4 "
• 7/8 "
• 1 "
• Made of high-carbon tool steel, these bits are protected in a wooden box.

Includes these HIGH QUALITY STEEL Jumbo bits:

• 2-1/4" Forstner Bit
• 2-3/8" Forstner Bit
• 2-1/2" Forstner Bit
• 2-5/8" Forstner Bit
• 2-3/4" Forstner Bit
• 2-7/8" Forstner Bit
• 3" Forstner Bit
• 3-1/8" Forstner Bit

Includes these HIGH QUALITY STEEL bits:

• 1/4"
• 3/8"
• 1/2"
• 5/8"
• 3/4"
• 7/8"
• 1",
• 1-1/8"

• 1-1/4"
• 1-3/8"
• 1-1/2"
• 1-5/8"
• 1-3/4"
• 1-7/8"
• 2",
• 2-1/8"

Includes these HIGH QUALITY STEEL bits:

• 1/4"
• 5/16"
• 3/8"
• 7/16"
• 1/2"
• 9/16"
• 5/8"
• 11/16"

• 3/4"
• 13/16"
• 7/8"
• 15/16"
• 1", 1-1/8"
• 1-1/4"
• 1-3/8"

• 1-1/2"
• 1-5/8"
• 1-3/4"
• 1-7/8"
• 2"
• 2-1/8"

Includes these HIGH QUALITY STEEL bits:

• 1/4"
• 3/8"
• 1/2"
• 5/8"
• 3/4"
• 7/8"

• 1"
• 1-1/8"
• 1-1/4"
• 1-3/8"
• 1-1/2"
• 1-5/8"

• 1-3/4"
• 1-7/8"
• 2"
• 2-1/8"
• 2-1/4"
• 2-3/8"

• 2-1/2"
• 2-5/8"
• 2-3/4"
• 2-7/8,
• 3"
• 3-1/8"

Includes these HIGH QUALITY STEEL bits:

• 1/4"
• 5/16" 3/8"
• 7/16"
• 1/2"
• 9/16"
• 5/8"
• 11/16"

• 3/4"
• 13/16"
• 7/8"
• 15/16"
• 1"
• 1-1/16"
• 1-1/8"
• 1-3/16"

• 1-1/4"
• 15/16"
• 1-3/8"
• 1-7/16"
• 1-1/2"
• 1-9/16"
• 1-5/8"
• 1-11/16"

• 1-3/4"
• 1-13/16"
• 1-7/8"
• 1-15/16"
• 2"
• 2-1/16"
• 2-1/8"

7-Piece Brad Point Set includes :

• 1/8"
• 3/16"
• 1/4"
• 5/16"
• 3/8"
• 7/16"
• 1/2"
  

  This starter set contains the most popular sizes for doweling.

These bits are made of precision-ground high speed steel (HSS) that keeps a sharp edge longer, resists wear and
possible overheating. Center brad point allows accurate positioning and prevents skating. Side cutting edges have
relieved backs to reduce friction and produce smooth side walls. In diameter sizes 1/8” to 1/2” in 1/64” increments.
Includes convenient plastic indexed storage box

Give wood screws more bite by preboringwith these tapered drill bits. This quality 22 piece set contains 7 drill bits
with countersinks, stop collars, and anstand up case. These bits let you drill perfect holes for #5 through #12 screws
with a 3/8” countersink.

Title Goes Here

This quality set features the most popular sizes of plug cutters in both straight and tapered styles. These high quality
carbon steel cutters make a smoothsided plug with rounded shoulders for easy insertion into a bored hole. The
plug remains snug in the wood until sawed out or removed with a screwdriver.

Sizes include: Tapered- 1/4”, 3/8”,
1/2”, and 5/8”, Straight- 1/4”, 3/8”, 1/2”,
and 5/8”.

Step Drills drill the pilot hole and the counterbore for your pocket-hole face frame assembly in one step. Available in two popular cutting angles; 45° for flat head screws and 90° for pan head screws. An excellent complement to the pocket hole guide.

Designed for use on a drill press, this fully Adjustable Circle Cutter will cut flat sided holes in wood from 1" to 5". Made of M-2 alloy steel, this Circle Cutter features a 3/8" hex shank, 5/16" drill, center point and Allen® wrench. The perfect after-market accessory to any drill press!