Auto Start Port The Summit Wet / Dry Shop Vac has a built in outlet for plugging a workshop machine or power too into it. When the machine or power tool plugged into the Power Port is turned on the Shop Vac starts, when the machine or power tool turns off the Shop Vac turns off with a approximate. 6 second delay to clear the hose. This is perfect for palm and orbital sanders and many other shop power tools.

EVERY WORKSHOP NEEDS A GOOD WET/ DRY VAC
AND THIS IS IT!

Compact, quiet and durable, the Summit Vac has all the features you look for in a wet / dry vac system. This wet/dry vac features a 110V single phase motor, that is not only powerful, but quiet. The powerful motor allows the vac to be used on most workshop power tools and machines as a dust collector. The Vac is also equipped with a two speed motor. Use the low speed setting for smaller tools like orbital sanders, and use the high setting for larger tools like routers and table saws. The Summit Vac
has a built in outlet for plugging a workshop machine or power tool into it. When the machine is turned on the Vac starts - when the machine is turned off the vac delays shutting off for approximate. 6 seconds to clean out the hose. This is perfect for palm and orbital sanders and many other shop power tools and machines. The unit comes with a full compliment of nozzles and extensions to make the job easier

Lightweight, flexible, and easy to maneuver, the Summit Small Power tool hose can be used on most any small power tool without getting in the way. The hose is perfect for use with tools like random orbit sanders, routers, biscuit joiners and more. The hose comes with a screw on adaptor and a rubber adaptor that will help adapt the hose to most small power tools. A large fixed screw-lock end is designed to be plugged directly into the vac inlet port and secures with screw-lock mechanism. This hose is designed to be used with the Summit Wet/Dry Vac. The hose measures 16' in length for extra reach and easy maneuverability

Having difficulty connecting odd sized tool openings or European size fittings? The Rubber fittings are a perfect solution. The soft rubber fitting will stretch, flex and give allowing for a tight connection on a number of small power tools.

Keep your dust collector conveniently out of the way with a Summit wall mounted dust collection system. This powerful system comes with a unique EZ-Mount wall bracket. This will allow you to mount the dust collector onto just about any wall in you shop. The EZ-Mount wall bracket is made out of heavy duty steel and fits into the two holes cutout in the base of the dust collector. This design allows you to remove the dust collector with out having to remove any bolts, just simply lift it off the EZ-Mount bracket and move the unit where you need dust collection. Add a second bracket for multiple mounting locations in your shop ( sold separately).

This powerful dust collector from Shop Fox® features an extra heavy-duty 12" steel impeller and a 1-1/2 HP motor that runs on 110V.

• Motor size: 1-1/2 HP, 110V, single-phase, 3,450 RPM
• Motor amp draw: 110V - 16A
• Portable base size: 21-1/2" x 33-1/2"
• Bag volume: 5.4 cubic feet
• Height (with bags inflated): 78"
• Bag size (Dia. x depth): 19" x 33" (2)
• Powder-coated paint
• Air suction capacity: Approximate. 1,280 CFM
• Impeller: Balanced steel, radial fin 12"
• 6" inlet with a removable "Y" fitting with two 4" openings
• Static pressure: 10.1"
• Standard bag filtration: 30 Micron
• Approximate. shipping weight: 120 lbs.

Designed for portability, the model W1727 1 HP Dust Collector can be moved from one machine to another when needed, instead of having to build an entire fixed dust collection system and running ducts to each machine. Some of the machines that this unit works well with are the oscillating drill presses, 13" planers, cabinet-style saws, bench-top and combination sanders, miter saws, floor sweeps, and stand-mounted dust collection nozzles.

• Motor: 1 HP, 110V/220V, Single-phase
• Amps: 9 @ 110V, 4.5 @ 220V
• Air suction capacity: 800 CFM
• Static pressure: 5.67"
• Number of 4" intake holes: 1
• Impeller: 9" balanced steel, radial fin
• Bag capacity: 2.1 cubic feet
• Portable base size: 15-3/4" x 39-3/4"
• Bag size (dia. x depth): 14-3/4" x 24-3/8" (2)
• Powder coated paint
• Height with bags inflated: 54-1/2"
• Approximate shipping weight: 59 lbs.

This SHOP FOX® Dust Collector features a 2 HP motor and an extra heavy-duty 12" steel impeller that moves 1,550 cubic feet of air every minute. When it comes to performance and value, this one is hard to beat!

A quality and economical replacement dust bag for your old worn out bag. The bags are available in two different sizes: 20" diameter by 401/2" long and 14" diameter by 291/2" long. The bags are
made from a durable plastic and comes in five packs. Designed for use with upright dust collectors that use both top and bottom bags. The bags work with the most common upright dust collectors. These are to be used on the bottom of the dust collector only.

Turn on your dust collector from anywhere in your shop with the NEW and Improved "Long Ranger II" Remote Dust Collector Switch.
Save yourself the inconvenience of walking over to turn on your dust collector when you find you're in the middle of a critical project. Simply press the transmitter on/off button to easily switch your dust collector on or off.

Advantages Of This Great New System Include:

• Simple, Reliable and
  foolproof operation
• 5 ft. cord on the receiver module.
• Heavy duty commercial quality construction.
• Convenient belt clip on transmitter
• Available in 110V and 220V versions
• F.C.C. approved
• Extra hand piece transmitters available.
• Multiple frequency codes
• Grounded w/reset button
• Uses R.F. signal, not affected by: Outside interference by large TV's, Transformers, electrical noise, or 3 Phase Power sources
• Transmitter need not be aimed directly at Receiver– can go through walls!

This Table Saw Safety Dust Guard is the ideal solution for table saw safety and dust control. When connected to a dust collection system, the Dust Collection Guard captures the dust thrown up by your table saw blade. The Guard can be used on any table saw with an extension table. It is very easy to install and easily swings out of the way. A unique counter-balance allows for fast & easy positioning.

Features and Specifications:

• Protects you from hazardous table saw debris
• Hood is constructed from one piece, clear shatterproof plastic
• Accepts saw blades up to 16 "
• Can use with dado blades.
• Allows tilts for 45degree cuts
• Adjusts easily to suit thickness of material being cut
• Accommodates splitter and anti-kickback pawls
• Connects to a standard 4" duct system
• Boom extends to a full 83"
• Can be mounted to ceiling for maximum clearance
• Easy setup and adjustment€¢ Easily swings out of the way
• Sturdy steel mast and boom construction
• Connects to 4" dust hose

The deluxe ceiling mount air cleaner from Shopfox comes with a 3 speed remote control with speeds ranging from
750 RPM to 1200 RPM. The air cleaner also has a dual filtration system and runs on 110v.

• Motor size: 1/5 HP, 115V, 60Hz, 1,725 RPM, Single-phase
• Motor amperage: 2 Amps, 2.5 Amps, 3 Amps
• 3 Motor speeds: 750 RPM, 960 RPM, 1,200 RPM
• Fan sound rating: 62 dB, 67dB, 69 dB
• Air flow: 556 CFM, 702 CFM, 1,044 CFM
• Primary filter: 5-micron, pleated type, 23-1/2" x 11-1/2" x 1"
• Secondary filter: 1-micron, bag type
• Unit dimensions 30-1/4 L, 24-1/8 W, 12-1/8 H
• Remote control
• Timed automatic shutoff
• Approximate shipping weight: 78 lbs.

This Pre-Made Down Draft Box comes with everything you need to draw harmful dust particles away from the user without obstructing the user's movement or productivity.

• 7" deep x 17-1/4" wide x 28" long down draft box (some assembly required) with baffles to direct saw dust towards dust port.
• 4" dust collection port / blast gate connects to your dust collection system for efficient dust/chip disposal (hose not included)
• Includes 64 non-slip rubber grommets to help stabilize your work piece while sanding or routing.
• Orange stops are also included to prevent stock movement while sanding and are able to be placed in any of the open holes on the plate(s).

Build your own custom downdraft table and finish it off with these steel down draft panels. Each plate measures 6-3/4" x 16-1/2" and has soft, non-slip rubber grommets to prevent marking the stock. Orange stops are also included to prevent stock movement while sanding and are able to be placed in any of the open holes on the plate(s). The set includes 2 down draft panels. Note: 4 panels shown in photograph

This 6" X 4" Y Adaptor has a 6" I.D. on the large inlet side and
3-15/16" O.D.'s on the two Y inlets. This Adaptor will adapt a single 6" O.D. pipe or connection to two 4" connections for 4" dust collections hose.