Panel Max & Panel Max XL
Glue Press System

Panel Max Pro System
Glue-up large or small panels with great looking, professional results every time with the Panel Max & Panel Max XL Glue Press System. The Panel Max makes stronger, more uniform joints than standard pipe or bar clamps. Unlike pipe or bar clamps, which tend to over-tighten on the bar side, The Panel Max applies even, uniform pressure to the stock surface since it completely surrounds the work piece, which creates superior quality joints with less hassle. This system also cuts the surface area required for glue-ups down about 90% since it is mounted vertically to any wall in your shop and stays out of your way while the stock is drying. When considering purchasing wide boards consider this; wide stock pieces cost more and tend to warp when purchased from a store or lumber yard; with the Panel Max Glue Press you can glue up a series of narrow boards to produce wide, warp-resistant panels for much less money. The Panel Max also aligns your boards better than standard clamps, resulting in your panels gluing up flat which will require less planing and surfacing. You can also add or remove clamp rails easily by sliding them out of the rails.
Panel Max Pro System Panel Max Pro System Panel Max Pro System Panel Max Pro System

Note: Wood & Wood Rails Not Included

The Panel Max system includes:

  • 3 each of the 43" clamps and hardware.
  • 1 each of the 39" mounting rails.
  • With one system you can glue panels up to:
    37" Tall x 48" Wide x 5" Thick
    (3" Recommended Thickness)
Download Instructions for Panel Max

The Panel Max XL system includes:

  • 3 each of the 55" clamps and hardware.
  • 1 each of the 39" mounting rails.
  • With one system you can glue panels up to:
    49" Tall x 48" Wide x 5" Thick
    (3" Recommended Thickness)
Download Instructions for Panel Max XL
No. Description
Price
Quantity
2952
Panel Max System
$349.99
555
Panel Max XL System
$399.99
2953
Add-ON Kit for Panel Max
2 each 43" Clamp Rails and 1 each 39" Mounting Rail
$249.99
556
Add-ON Kit for Panel Max XL
2 each 55" Clamp Rails and 1 each 39" Mounting Rail
$274.99
2954
1 each 43" Clamp Rail
For Panel Max
$119.99
2955
1 each 39" Mounting Rail
for Panel Max or Panel Max XL
$24.99
Product Divider Image

4-Way Clamping System

Our 4 Way Clamping System applies equal pressure from all four directions (top, bottom,
and both sides). Ideal for gluing table tops, shelving, veneer, and laminates.
Attach clamps to any length 2 x 2’s with screws provided, set jig and turn handle to
tighten. Clamp has plastic pressure pads and two 19-1/2” tail bars of tough plastic
with 12 notches to handle a variety of stock widths. Wood is not included. Replacement
Bars are also available for the Four Way Clamp and come in a package of four.
The replacement bars are all approximately 121/2" in length.
No. Description
Price
Quantity
670
4 Way Clamping System (1 each)
$28.99
612
Replacement Bars (4 pack)
Note: Replacement bars can be used to make up different length clamping rails. Just use the same end clamps on multiple setups.
$10.99
Product Divider Image

General Tools EZ Joiner Aluminum Clamp Board-Straightening Kit

Mount clamps to table-saw guide board to create a straight reference guide to strengthen any length of lumber

General Tools EZ Joiner Aluminum Clamp Board-Straightening Kit

 

The General Tools EZ Joiner Aluminum Clamp Board-Straightening Kit is intended to help you straighten crooked boards, true-up rough-sawn edges and make shallow taper cuts with positive control.



  • Fits any length of stock up to 2 in. thick
  • Straighten crooked boards, true-up rough-sawn edges and make shallow taper cuts with positive control
  • Aluminum construction
  • Mount clamps to table-saw guide board to create a straight reference guide to strengthen any length of lumber (guide board and table saw not included)
  • Helps you attain a straight edge with just 1 pass
  • Includes 2 clamps and 4 threaded screws with flat board supports
No. Description
Price
Quantity
20872
General Tools EZ Joiner Aluminum Clamp Board-Straightening Kit
$18.99
Product Divider Image

Pinch Dogs

Pinch Dogs
Drive a Pinch dog into an end grain along a wooden joint, doing this allows the steel tapered pinch dog clamps to draw boards tightly together for gluing up panels, table bench tops and more. You can use the Pinch Dogs repeatedly without the worry of them twisting, bending or breaking. Use them to square corners. Pinch Dogs can also be used for column assembly.
No. Description
Price
Quantity
801
1-1/2" Pinch Dogs (10 pack)
$19.99
802
2" Pinch Dogs (10 pack)
$20.99
Product Divider Image