Check your table saw compatibility here.

Dubby...the Original Crosscut Sled

No miter gauge on the market can offer you the margin of safety provided by this “sled”. The versatile hold-down clamp included with every Dubby will give you an extremely safe way to cut small pieces, and will easily pivot out of the way when you don’t need it. With 35 lbs. of hold-down pressure, the clamp will hold small pieces as you cut them with your fingers out of harms way.The Dubby system is available in three different packages: Left Side Cutting package, Right Side Cutting package, and the Deluxe Double Dubby package, which includes both the left and right side Dubby’s.

This easy to use jig will allow you to make repetitive thin rip cuts on the left side of the saw blade on your tablesaw. This eliminates the danger of binding the stock between the blade and the fence reducing the risk of kick back. Whether you need to cut two strips or two hundred this jig makes any size job fast and simple. The jig incorporates a double locking system - A single large star knob secures the position of the jig and locks the jig into a standard 3/4" x 3/8” deep miter slot simultaneously. On the tip of the jig there is a ball bearing guide which keeps the stock firmly up and against the fence for great repeatability. The main body of the jig is made from single piece of extruded aluminum for superior strength and durability. The thin rip jig adjust from 1-1/8" from the miter track to 5-1/2" away from the miter track for making various width cuts. For Craftsman and other undersized miter slots, It may be necessary to Sand down the side of the miter bar on the Thin Rip Jig for proper fit.

Safety Note: When cutting thin strips on your table saw you must use a Zero-Clearance inset (sold separately) to prevent the stock from binding between the blade and factory insert.

Kreg Precision Router Table Setup Bars make adjustments to router tables, shapers and table saws very simple and very precise. Unique design straddles the router bit or saw blade to allow for more precise height adjustment. Step on the top edge of each setup bar acts as a gauge to test the depth of your completed cuts. Step on the end of each setup bar used to test the fence depth of a tablesaw blade or router bit. Made from a soft aluminum designed to prevent damage to your router bit or saw blade if contact is made during setup. Set includes 7 setup bars stored in a portable case that protects the bars and makes it easy for woodworkers to locate the correct bar for their application. Sizes: 1/8, 3/16, 1/4 5/16, 3/8, 7/16, 1/2.

• Unique design straddles the Router Bit or saw blade to allow for more precise height adjustment
• Step on the top edge of each setup bar acts as a gauge to test the depth of your completed cuts
• Step on the end of each setup bar used to test the fence depth of a table saw blade or Router Bit
• Made from a soft aluminum designed to prevent damage to your Router Bit or saw blade if contact is made during setup

If you are short on space in your shop, this extension kit is a must for any table saw.

The great feature of this extension table is that it will fold down out of the way, or come completely off the table saw in a matter of seconds. This 16" extension kit will fit light duty, heavy duty, and contractor saws which have a motor hanging out the back of the saw.

Table Saw Extension Kit Includes:

Adjustable work-support is constructed for heavy-duty use! Adjusts in height from 24-1/2-Inch to 42-1/4-Inch. Unique design provides superior stability. A single, quick folding leg for easy set up and storage. Non-marring wide T-bar base ensures stability. An easy rolling, 13” x 2” galvanized dual ball bearing roller.150 pound capacity.

With the PALS on your saw, "pounding" the trunnion into place using a hammer & block of wood are gone forever!

The A-Line-It was selected as the "Top Value" in the WOOD Magazine article that compared woodworking machine alignment tools.

• The perfect tool alignment system for hobbyists and small shops.
• The 1" capacity dial indicator reads in .001" increments for absolute precision.
•Self-adjusting "Smart Bar" so the perfect fit in the miter groove is automatic.
• Leveling knobs adjust for any miter groove depth.
• On a table saw, it will allow you to test table saw alignment, arbor shaft run out, saw blade run out, rip fence alignment, and fence straightness.

Most woodworkers already have a dial indicator laying around the woodworking shop, either on some sort of gauge set that never worked the way you thought it should or tucked away in the tool box waiting on a good way to use it.

• Add your shop dial indicator to the A-Line-It Smart Bar System and you get the perfect tool alignment system for hobbyists and small shops.
• Self-adjusting "Smart Bar" so the perfect fit in the miter groove is automatic.
• Leveling knobs adjust for any miter groove depth.
• On a table saw, it will allow you to test table saw alignment, arbor shaft run out, saw blade run out, rip fence alignment, and fence straightness.
• Works with digital and standard 1" capacity dial indicators.

Increase the versatility of your dial indicator by turning it into a multi-purpose gauging tool. This 22 piece assorted tip set allows you to change you existing dial indicator tip to one that is just right for the job at hand. The contact points will fit most any dial indicator with 4-48 threads.

The Uni-T-Fence is a heavy duty aluminum extrusion up grade fence for the Delta® Unifence Table Saw Guide System designed by Might-T-Track Inc. It replaces the Stock Delta Fence

BOARD MATES
ANTI-KICKBACK HOLD DOWN DEVICES

Board Mates use non-marring neoprene rubber wheels that turn clockwise only, these wheels work as anti kickback and hold down devices. The Board Mates body is made of die-cast aluminum with a spring loaded swing arm that applies pressure down on a work piece as it rolls under the anti-kickback wheels. The Board Mates system has adjustments for spring tension as well as forward and backwards body adjustment after mounting. Board Mates come in pairs which can be mounted on fences 1-1/2” to 3” high x 1” or wider. Each Board Mate consists of mounting bracket, swing arm body with spring, and a adjustable roller.

• Yellow Board Mates are for table saws and router tables

• Green Board Mates are for shapers

• Orange Board Mates are for radial arm saws

The EZ Square Table Saw Rip Fence is the perfect aftermarket fence if you're serious about saving time and making straight cuts. The EZ Square Table Saw Fence was designed to be that dependable piece of equipment in your workshop that you can trust every time you use it. It takes a simple, no-frills approach that gets the job right every time.
The EZ Square Table Saw Fence fits most saw and some drilling may be required.

• T-Slots on the fence top and front and back faces let you mount all sorts of accessories like Board Buddies and Featherboards.
• The EZ Square Fence can be used right or left of the saw blade.
• UHMW Face on both left and right faces means super smooth operation.
• T-Track mounting of the fence rails means the fence rails can be adjusted  to the left or right without re drilling.
  

Our custom made Board Buddies / Board Mates mounting bracket set (1 pair) make mounting and adjusting your Board Buddies a snap. Made of UHMW comes with bolts and knobs.
Fits our Mini T-Track (For 1/4" Hex Head Bolt)

Link Belts reduce vibration in any belt driven machine! Common V-belts develop a "memory" and retain their non-operating shape causing annoying and unnecessary machine vibration. Unlike V-belts, these specially engineered link belts do not develop a "memory", but retain their flexibility for smooth operation. Link Belt is 1/2" wide.

Cut perfect miters consistently with the Precision Miter Gauge System. A number of unique features makes this the most accurate miter gauge on the market today. Factory calibrated accuracy starts with a gauge head that is machined on a computerized milling machine for absolute precision. An easy-to-read Vernier scale enables precise angle adjustments up to 1/10th of a degree. Five patented bar adjusters take up the play in the table slot for a perfect fit. A 24” Heavy Duty Track section with patented flipstop and self-adhesive measuring tape is included.

This clamping miter gauge is safer than your standard miter gauge since it keeps your hands away from the blade. It has a comfortable grip, built in sliding stop, and a positive trigger clamping action. It fits all 3/4” x 3/8” standard miter slots and has positive angle stops at 90° and 45° both left and right.

This Delta Miter Gauge is accurately constructed with adjustable positive stops at 90, 15, 22-1/2, 30, 45, and 60 degrees left and right. The 18-1/4” guide bar offers adjustment screws to custom fit the miter slot of your machine. A large hand knob provides positive control of the miter gauge.

Attach the cam miter hold down directly to your miter gauge by simply threading it into the top center hole. Once secure, place the stock you want to crosscut on your table saw and slide it squarely up against your miter gauge. Adjust the rubber foot height so that it fit's snuggly against the stock. Clamp the stock down by pushing the cam lever downward until you have the desired pressure to hold your stock, and proceed to making your cut. The cam miter hold down works on miter gauges with 1/2" - 20 thread holes.

The 22'' Miter-T-Fence will improve work support close to the blade and will work on the left side or right side of your saw.The adjustable extruded aluminum fence increases the face of your miter gauge or miter saw and has a built in extension bar to increase the stop capacity to 36''. This fence can also be put onto your Miter saw for perfect repetitive cuts and a better extension. The fence can be easily taken on and off either tool to switch back and forth between tools. The 48'' fence is designed for your miter saw with a built in extension capacity of 86''. This fence can be used in conjunction with the 22'' fence to give your miter saw a fence for both sides for the ultimate fence system your shop will ever know.

Both fences include a stop block for the repetitive cuts and appropriate knobs and bolts for easy mounting on and off your various tools.

Use this UHMW to make jigs and fixtures for your table saw , router table, etc. These easy to cut 4'' x 36' 'sheets come in several thickness. Also use the 3/4" x 3/8" plastic strips to make sliding table jigs for your table saw, band saw or router table.

Ultra high molecular weight polyethylene self-adhesive tape is perfect for jigs, drawers, fences and fixtures--wherever you need to make sliding parts slide easily. It's the right way to perfect your Delta table saw tenon jig, or to make that homemade miter fence glide smoothly across your saw. If it needs to slide you can either do something temporary (over & over) or you can use Slick Tape.

Table saw blade insert improves the safety and efficiency of your table saw. The insert closes the large factory insert gap which makes your saw safer and can even improve dust collection.The insert is blank so you can custom fit the blade slot by passing your blade up through it.

Buy two, one for your regular saw blades and one for your dado blade.

Deluxe Wooden Featherboard
Quick positioning feather board keeps stock tight against the fence and flat to the saw table while cutting. Prevents chatter and dangerous kick-back. Locks into standard miter slots with a quick twist of the knob. 4-1/2" adjustment slot, 9/16" thick x 1-3/4" wide x 10" long

Our compact, Universal Fence Clamps allow you to secure a variety of shop made auxiliary fences to your existing table top fences without having the clamp block your work. The clamp arm simply fits into a 3/8” hole in the top of the auxiliary fence, keeping the clamp out your way. That simply means no more cumbersome wood screws or C clamps, and no need to screw into your expensive fence! Works great for table saws, band saws, cutoff saws, router fences. Clamps come in sets of 2.

When making auxiliary fences most of us have the issue of our clamps getting in the way of the cut or in our line of site. With these new fully adjustable fence clamps, that problem disappears. These clamps won't interfere with your work and they can be used on many shop made auxiliary fences. The clamp pin will fit into a 3/8" hole drilled into your auxiliary fence. Note: Your fence should be at least 3/4" thick to ensure that there is enough clearance for the
3/8" hole. When fully extended the clamp measures approximately 5-3/4" in clamp capacity, which means it will fit almost any size tablesaw fence. With these clamps you won't have to worry about using those cumbersome C-clamps or wood screw clamps. More importantly you don't have to drill screw holes into your expensive
fence(s). The Adjustable Fence Clamps work great on tablesaw fences, router fences, re-saw fences for the bandsaw, and more. You can also use the clamps individually with a block of wood for a stop block. Each package comes with a set of two fully Adjustable Fence Clamps.

Easy one touch calibration

The ZeroPlay Guide is a "One-Touch Calibration" miter bar(9-1/2" in length) that has two stacked half bars with opposing wedges's that expand parallel evenly to fit the exact width of a standard miter slot for a perfect fit and smooth glide, even fits the tricky Shopsmith™ or General's miter slots. Because the ZeroPlay Guide Bar is full profile miter bar that fits the exact width of the miter slot, you have no side to side play in the miter slot.The ZeroPlay Guide Bar is for those who demand absolute accuracy and have zero tolerance for mistakes. Build better jigs in less time! ZeroPlay Stops serve as an anchor for your clamping devices within the miter slot-shop build clamp plan is included. Build a table saw coving fence and more with the ZeroPlay. ZeroPlay Stops limit the travel distance for most any specialty Jig.

Originally designed for the Dubby cut off sled, the Dubby Miter Bar can now be purchased separately for use on jigs and fixtures throughout your shop. With unique steel plungers, combined with the precision machined steel bar, the Dubby 24" Miter Bar works great with most any sled fixture in your shop. The plungers can be adjusted so there is virtually no side to side play. The bar comes with 4 machine screws for easy mounting to sled platforms. The bar measures 24" in length and fits standard 3/4 x 3/8" miter slots.

Finally a universal Precision Miter Bar for building virtually any sled or miter slot jig. With adjustable spring plungers, the miter bar maintains constant pressure against the walls of the miter slot so you have virtually no play side to side, while being able to slide through the slot with ease. The bar fits most standard 3/4” x 3/8” miter slots. Made of hardened steel the Precision Miter Bar will not bend or twist like some of the plastic bars you may have. This is the perfect accessory for anyone who likes to build their own jigs and fixtures and who is concerned with quality.

The perfect accessory kit for attaching featherboard, hold-downs or virtually any type of jig you can think of to your table saw, router table, or any tool with a standard 3/4" x 3/8" miter gauge slot. The fixture kit works by applying outward pressure to the "walls" of the miter gauge slot. The "wedge" bolts push up into center counter sunk holes in the miter bar as they tighten with the star knobs, which pushes the center of the miter bar outward producing a nice tight fit.

The Fixture Kit includes:

• 2 ea. expandable 4 3/4" long miter bars
• 2 ea. star knobs
• 2 ea. wedge bolts
• 2 ea. washers
• can be used with stock up to 1-1/4" thick

When you need to make that slightly angled cut that is to long for your miter or chop saw, use the taper jig to make the job easier. Constructed of aluminum , this taper jig includes a built-in scale and is fully adjustable. Also has a backside stop to hold wood in place. It may be assembled for either left or right hand use. Use it with your rip fence to cut tapers up to 15 degrees (this is a 3” taper per foot). Overall length is a generous 24”

Cove Cutting Table Saw Jig

Give your projects a custom look by making your own moldings. No more messing with all those clamps to secure your jigs to your saw. The system uses your miter slots to secure the the cove jig to your table saw, or use four 30mm Magswitch™ magnets (not included). This unique design allows for fast easy set up for stock 7” wide and 1½” thick. By angling your table saw blade it will create elliptical coves that you won’t find in lumber centers. The Cove Cutting Table saw Jig includes a featherboard hold down, 4 miter slot locking devices and all the necessary hardware.

Cove Cutting Table Saw Jig Instructions

Safety, accuracy and repeatability are the hallmarks of this heavy-duty tenoning jig. Designed to fit any table saw with a 3/4' X 3/8' miter groove, this jig will hold your stock in a precise position. The adjustable back stop will support stock from 0 degrees to 45 degrees. The width of the cut is controlled with a fine-threaded adjustment knob. Constructed of cast iron and steel.

If you're planning on making a sliding jig or fixture for your woodworking shop, the INCRA Miter Slider is exactly what you need. These inexpensive aluminum runners adjust for PERFECT sliding action in any standard (or near standard) 3/4" by 3/8" miter gauge slot with just a twist of the wrist. They lock firmly in place with another twist of the wrist. Won't warp, shrink or swell like wooden runners. Includes plans for a wide variety of shop-made jigs and fixtures. Anodized aluminum for durability and beauty

INCRA Steel Miter Sliders. The INCRA Miter Slider SE combines the versatility of the INCRA Build-It products with the unique performance and feel of the adjustable GlideLOCK miter bar used on INCRA miter gauges. Miter Slider SE is not recommended for stationary jigs that must be locked into position within a miter slot; choose standard aluminum Miter Slider for these applications.