Clamps & Accessories

90° Corner Clamp

Our 90° Angle clamp features the power flex handle, which allows you to pull the handle out and rotate it to apply extra holding power to your stock. The clamp is perfect for gluing up frames, T-miters or just holding the stock in place. The unique design of the clamp automatically adjusts to the thickness of your stock as you tighten. Two holes are pre drilled on the bottom side of the clamp to accept table clamps (not included- sold separately) to keep the 90° clamp secure to the table top.

Features:

• Power flex handle allows you to pull the handle out and rotate it to apply extra holding power to your stock
• Perfect for gluing up frames, T-miters or just holding the stock in place
• Automatically adjusts to the thickness of your stock as you tighten
• Two holes are pre drilled on the bottom side

Note: Table clamps not included.

Table Clamps

Table Clamps are designed for use with the 90° Corner Clamps. There are two pre-drilled holes on the bottom side of the 90° Corner Clamp that allows the Table Clamps to fit snug & firm. This allows the 90° Corner Clamp to be secured to any work bench or table top and hold your work piece in place. 2 Pack

Features:

• Designed for use with the 90° Corner Clamps
• Allows the 90° Corner Clamp to be secured to any work bench or table top and hold your work piece in place
• 2 Pack

Includes:

• 2 ea. Fulton Table Clamps

Note: Requires one pair Table Clamps for one 90° Corner Clamp.

Spring Miter Clamp Set

These Spring Clamps are the ideal and cost effective way to quickly and easily clamp mitered corners without all of the hassle you typically have with other clamps. The Spring Miter Clamps are made from a high strength steel. The clamps can be applied using the easy to load, Spring Tensioned Pliers to make it super easy to to spread the tips apart. Great for moldings, trim and frames.
›See more product details

×

Spring Miter Clamp Set PDF Instuctions

Close

×

Spring Miter Clamp Set

If you have ever attempted to firmly secure and clamp mitered corners then you know what kind of a challenge it can be to say the least. You could always try those large, cumbersome and very expensive parallel clamps to try and work each corner just right to hold your mitered corners together. That too can be extremely challenging and not to mention very costly

These Spring Clamps are the ideal and cost effective way to quickly and easily clamp mitered corners without all of the hassle you typically have with other clamps. The Spring Miter Clamps are made from a high strength steel. The clamps can be applied using the easy to load, Spring Tensioned Pliers to make it super easy to to spread the tips apart.

A Complete Set for The Workshop or Jobsite!

Clamping odd angles with standard clamps can be challenging. Our Spring Miter Clamps set is designed to make this application easier and much less time consuming. With the spring loaded pliers and steel spring clamps you'll be able to quickly clamp 45 degree mitered corners in seconds! The set comes in a super convenient carrying case which makes it perfect for working in your workshop or taking with you on the jobsite!

Keeping it together

Each steel spring clamp provides the perfect amount of tension to hold the corners of your project together. You can then use a brad nailer to secure the corners or, simply let the glue dry if it was applied prior to clamping.

Clamp Using the Pocket Hole

The steel pin on this clamp is shaped to fit snugly into a pocket hole, securely anchoring one workpiece against the other for easy assembly. Just drive a screw into an adjacent pocket hole while the Right Angle Clamp holds the piece steady for you.

The Perfect Pliers for Spring Miter Clamping

With these spring tensioned pliers and top and bottom clips for multiple size spring clamps, these pliers are the perfect pliers for use with these spring miter clamps. The pliers also have a comfortable rubber grip for extended periods of use.

Quick and Easy

While holding one side of a spring clamp in place against a plier clip, simply put firm pressure on the other side of the spring clamp to snap it on to the pliers. Once loaded, you are ready to apply the clamp to the corner of your work piece.

Squeeze to Spread

Once the pliers are loaded with a clamp, simply squeeze the spring loaded pliers to spread the clamp. The more you squeeze the pliers, the wider the spring clamp opens. This allows you to quickly apply the spring clamp to a corner of your workpiece and keep the corner in place

What does it come with?

• 4 ea. 1/2" to 3/4" Spring Clamps
• 4 ea. 11/16" to 1" Spring Clamps
• 4 ea. 7/8" to 1-13/16" Spring Clamps
• 4 ea. 1" to 1-3/8" Spring Clamps

• 4 ea. 1-3/4 " to 2-3/16 " Spring Clamps
• 4 ea. 2-1/2" to 3" Spring Clamps
• 1 ea. Spring Clamp Spreader/Plier
• 1 ea. Plastic Carrying Case

Close

The kit Includes:

• 4 ea. 1/2” to 3/4” Spring Clamps
• 4 ea. 11/16” to 1” Spring Clamps
• 4 ea. 1“ to 1-3/8” Spring Clamps
• 4 ea. 7/8” to 13/16” Spring Clamps
• 4 ea. 1-3/4 “ to 2-3/16 “ Spring Clamps
• 4 ea. 2-1/2” to 3” Spring Clamps
• 1 ea. Form fitted storage case
• 1 ea. Spring Clamp Spreader

Each size clamp is available in 8pc replacement packs
(8 clamps of the same size are in each pack 2993 - 2997).

WS-1 Light Duty Corner Clamp

Economical alternative for fixed 90 degree angle for miter or butt joints. Mounting holes to fix to work surface. Adjusts to various sized work pieces with 2 spindles. For light duty clamping.

Features:

• Mounting holes to fix to work surface.
• Adjusts to various sized work pieces with 2 spindles
• For light duty clamping

Clamping Capacity: Up to 3"

Range of Angle: 95°

90° Angle / Corner Clamps

The Bessey angle clamps are designed to hold, fix and align material at right angle and automatically adjust to different wood thickness.
›See more product details

×

90° Angle / Corner Clamps

The Bessey angle clamps are designed to hold, fix and align material at right angle and automatically adjust to different wood thickness. Their accuracy makes these the clamps for a number of applications, including cabinetry, furniture assembly and their compact size makes them easy to store.

Features

• Holds and aligns material at 90°
• For T joints and mitered corners
• Galvanized spindle with large threads.
• Accurate and super durable jaws.
• Plastic coated jaws to protect wood.
• Wide open design to allow room to dowel, screw,or stable material together while gluing.

Close

Features:

• Holds and aligns material at 90°
• For T joints and mitered corners
• Galvanized spindle with large threads.
• Wide open design to allow room to dowel, screw,or stable material together while gluing.

WS-3

• 1-3/16" maximum passage for T joints.
• Opening Accommodates up to 2-3/16" per side
  

WS-6

• 2-7/16" maximum passage for T joints.
• Opening Accommodates up to 4" per side

Table Mount Clamps

Works Bessey® WS-3, WS-6, S-10, S-15, and K-Body® Revo™ to work surface. Add Table Mount clamps to holes on handle side of clamp to any surface up to 2-1/4" thick.

Features:

• Holds Bessey® WS-3, WS-6, S-10, S-15, and K-Body® Revo™ to work surface

Works with:

• Bessey® WS-3
• Bessey® WS-6
• Bessey® S-10
• Bessey® S-15
• Bessey® K-Body® Revo™

Includes:

• 2 ea. Bessey Table Mount Clamps

90° Corner Clamp

The Kreg® 90° Corner Clamp gives you the helping hand you need to hold 90° corners and “T” joints together securely when you’re assembling boxes, drawers, cabinets and cases. Plus, the 90° Corner Clamp leaves both of your hands free to add your fasteners.
›See more product details

×

90° Corner Clamp

The easy way to hold 90° corner joints and “T” joints in boxes, cabinets, and cases
The Kreg® 90° Corner Clamp gives you the helping hand you need to hold 90° corners and “T” joints together securely when you’re assembling boxes, drawers, cabinets and cases. Plus, the 90° Corner Clamp leaves both of your hands free to add your fasteners.

Kreg® 90° Corner Clamp Features

• Works on 90° corners and “T” joints
• 1" maximum capacity
• Cast aluminum “V” and wedge clamp pads
• Automaxx® auto-adjust technology
• Easy-to-regulate clamping pressure with thumbwheel
• Cutout allows driving a pocket-hole screw without removing clamp
• Padded, ergonomic handles
• Self-squaring; automatically aligns joints to 90° angle; Automaxx™ auto-adjust technology

The 90° Corner Clamp is the fastest, easiest-to-use corner clamp you can buy thanks to Kreg Automaxx® auto-adjusting technology.

Helps Hold Assemblies Like Boxes, Cabinets, Drawers and Cases

The 90° Corner Clamp helps hold assemblies like boxes, cabinets, drawers and cases together to ensure that you get strong, tight-fitting assemblies—whether you’re using Kreg pocket-hole joinery, or another method.

V-wedge Jaws Ensure a Secure Grip

The clamp’s V-wedge jaws grip the mating pieces securely, ensuring that the pieces sit at precise 90° angles while you drive in Kreg Screws, or even another type of fastener, such as a nail or wood screw.

All-Metal Construction

The 90° Corner Clamp features all-metal construction, including cast-aluminum pads—an outer "V" and inner wedge—that press against the inside and outside faces of the two pieces being joined in order to hold those pieces at a 90° angle to one another.

Edge Stops Help Align the Edges

Edge stops also help align the edges of the pieces to ensure accurate assembly of structures like boxes, cabinets, drawers, and cases.

Automaxx® Auto-adjust Technology

Thanks to Automaxx® auto-adjust technology, all you have to do is squeeze the clamp handles. The clamp will automatically close with the amount of pressure you have set, regardless of the material, whether you’re using thin plywood for drawers, or materials up to 1" thick.

Close

Features:

• Works on 90° corners and “T” joints
• 1" maximum capacity
• Cast aluminum “V” and wedge clamp pads
• Automaxx® auto-adjust technology
• Easy-to-regulate clamping pressure with thumbwheel
• Cutout allows driving a pocket-hole screw without removing clamp
• Padded, ergonomic handles
• Self-squaring; automatically aligns joints to 90° angle; Automaxx™ auto-adjust technology

Right Angle Clamp

The Right Angle Clamp makes projects with 90° joints faster and easier than ever by giving you the helping hand you need to hold the parts in position as you drive in the screws. Just slip the pin on the Right Angle Clamp into a pocket hole, close the clamp, and it draws the mating pieces tightly together. The swiveling clamp pad opposite the pin grabs the mating piece securely.
›See more product details

×

Right Angle Clamp

The secret weapon for pocket-hole construction—now with Automaxx® Technology
The Right Angle Clamp makes projects with 90° joints faster and easier than ever by giving you the helping hand you need to hold the parts in position as you drive in the screws. Just slip the pin on the Right Angle Clamp into a pocket hole, close the clamp, and it draws the mating pieces tightly together. The swiveling clamp pad opposite the pin grabs the mating piece securely.

Right Angle Clamp Features

• 3-1/2" reach (89mm); clamps materials up to 31/8" thick (79mm)
• Auto adjusts to match material thickness
• Steel pin fits snugly into pocket hole
• Swiveling pad secures mating piece
• Adjustment knob provides easy-to-regulate clamping pressure
• Ergonomic padded grips prevent hand fatigue

Ultra-Wide Reach

Whether you’re joining two thin drawer sides for a cabinet, or thicker materials to frame an outdoor project, the Right Angle Clamp opens wide to get the job done.

Auto-Adjust Technology

Thanks to Automaxx® Auto-Adjust Technology, the Right Angle Clamp adjusts to match the material automatically with a simple squeeze of the handles. This handy clamp works with all kinds of materials, from thin 1/2" plywood to thick 2x4 boards.

Swivel Pad for Solid Clamping

The arm opposite the pin features a pad that swivels to fit tight against your material, so you can count on solid clamping without a chance of the joint shifting.

Clamp Using the Pocket Hole

The steel pin on this clamp is shaped to fit snugly into a pocket hole, securely anchoring one workpiece against the other for easy assembly. Just drive a screw into an adjacent pocket hole while the Right Angle Clamp holds the piece steady for you.

Use One Clamp, or Use Two

Many woodworkers find it handy to use two Right Angle Clamps when assembling large workpieces. Place a clamp on each end to hold the wood while you drive screws in the remaining pocket holes.

Close

Features:

• 3-1/2" reach (89mm); clamps materials up to 31/8" thick (79mm)
• Auto adjusts to match material thickness
• Steel pin fits snugly into pocket hole
• Swiveling pad secures mating piece
• Adjustment knob provides easy-to-regulate clamping pressure
• Ergonomic padded grips prevent hand fatigue

Clamping Squares

90° angle can be challenging more often than not. A simple solution is to place a square in the corner nof the two stock pieces you need to square and secure with a set of clamps, this however can be frustrating. Now with our Clamping squares, you can do just that without having to find a square thick enough to accept a standard clamp.
›See more product details

×

Clamping Squares

90° angle can be challenging more often than not. A simple solution is to place a square in the corner nof the two stock pieces you need to square and secure with a set of clamps, this however can be frustrating. Now with our Clamping squares, you can do just that without having to find a square thick enough to accept a standard clamp. The clamping squares are 3/4" thick to make clamping and placement a breeze. Each square is made from aluminum and machined with a tolerance of +/- .001. The squares have beveled edges and are anodized to resist staining. The squares are available in two sizes: 2-3/4" and 6" and come in packs of two.

Features

• 3/4" thick to make clamping and placement a breeze
• Each square is made from aluminum and machined with a tolerance of +/- .001
• Beveled edges
• Anodized to resist staining
• Available in two sizes: 2-3/4" and 6"
• Comes in packs of two.

Close

Features:

• 3/4" thick
• Each square is made from aluminum and machined with a tolerance of +/- .001
• Beveled edges
• Anodized to resist staining
• Available in two sizes: 2-3/4" and 6"
• Comes in packs of two.

Note: F-Clamps not included.

Square 90

This simple and affordable Square 90 becomes your third hand while assembling cabinets, drawers or any project that requires a 90° corner to be held in place while assembling. Made from high impact polycarbonate, the Square 90 is strong enough and durable enough for any project. Use any Clamp (sold Separately) to secure the Square 90 while assembling your projects. The Square 90 is available in 4" or 6" size and can be clamped on the inside or outside corner of your work piece making this a very versatile Clamping Square for any project. Achieving 90 degree corners just became a whole lot easier!
›See more product details

×

Square 90

The simple and easy to use Square 90 will become your third hand while assembling cabinets, drawers, boxes or any project that requires a 90° corner to be held in place while assembling. You can use the Square 90 in multiple situations where a 90 degree angle is needed.

Square 90 Positioning Squares

The Square 90 can be used on a standard 90, a t-joint, outside 90 degree, all four corners and more! Made from high impact polycarbonate, the Square 90 is strong and durable enough for any project. It can be clamped on the inside or outside

Standard 90 Degree

Simply clamp the Square 90 Positioning Square to the two pieces you want to be 90 degrees and adjust the square until your set. Secure the square with the two clamps.

All Four Corners

You can never have too many clamps and the same goes for Square 90's. The more you have, the more 90 degree angle projects you can square up at once.

T-Joint Corner

It even does T-joint or offset joint right angles.

Outside 90 Degree

You can use the Square 90's on the inside of a joint or even the outside of a joint!

Close

Features:

• Can be clamped on the inside or outside corner of your work piece.
• Can be used on a standard 90, a t-joint, outside 90 degree, all four corners and more
• Embossed graduation marks on both sides of each square
• Made from high impact polycarbonate

Note: F-Clamps not included.

Variable Angle Band Clamp - VAS

Whether you need to repair a chair, fix a frame or clamp four corners all at the same time, Bessey's Variable Angle Strap Clamp adapts to whatever situation you need.

Features:

• Strap Lock — an easy-to-use mechanism for releasing and locking the strap around awkward or large assemblies.
• Specially woven 23' polyester strap for up to 1,100 lbs tensile strength with minimal stretch.
• Geared winder allows for precise adjustment — tightens strap evenly from both sides for distortion-free clamping.
• Strap winder keeps excess strap conveniently stored on spool.
• Corner clip with swivel pads clamp any angle from 60° to 180° — four clips are included with clamp.

Includes:

• 1 ea. Variable Band Clamp
• 4 ea. Vario Corner Clips

Merle Band Clamp

Flexible jaw inserts are non-marring and are easily removed. They're made of high impact ABS plastic for long life and heavy use. The dual pivot feature allows the Merle to clamp virtually any size or shape securely! Perfect for circles and ovals, plus triangles, hexagons, octagons, and more. 23-foot steel banding included. The Merle clamp has almost no capacity limitation! Clamps as small as 2-5/8" x 2-5/8 to69" x 69" or 23-feet around, but can be extended to any length by using standard 3/8-inch steel banding or strapping. The Merle clamp will hold any type of frame for easy gluing, nailing or screwing.
›See more product details

×

Merle Band Clamp

Flexible jaw inserts are non-marring and are easily removed. They're made of high impact ABS plastic for long life and heavy use. The dual pivot feature allows the Merle to clamp virtually any size or shape securely! Perfect for circles and ovals, plus triangles, hexagons, octagons, and more. 23-foot steel banding included. The Merle clamp has almost no capacity limitation! Clamps as small as 2-5/8" x 2-5/8 to69" x 69" or 23-feet around, but can be extended to any length by using standard 3/8-inch steel banding or strapping. The Merle clamp will hold any type of frame for easy gluing, nailing or screwing. Even jointing force at all corners. It's excellent for wide cabinet type frames (use in the center or edges), and also for narrow picture frames. The adjustable Merle clamp allows you to use as much or as little clamping pressure as needed. Cast aluminum and steel construction makes the Merle clamp a tough tool that will work hard and long for you. Quick Release Corner Clips pull off with finger pressure. Just clip on more corners and get to work!

Features

• Clamps as small as 2-5/8" x 2-5/8 to 69" x 69" or 23' around
• Clamp any shape with ease
• Self-adjusting, non-marring jaw inserts align to any angle
• Perfect for cabinet frames and picture frames
• Quick release corners allow quick adjustment

Close

Features:

• Clamps as small as 2-5/8" x 2-5/8 to 69" x 69" or
  23' around
• Clamp any shape with ease
• Self-adjusting, non-marring jaw inserts align to any angle
• Perfect for cabinet frames and picture frames
• Quick release corners allow quick adjustment

X-Treme Clamp Tape

X-Treme tape quick clamp wrap eliminates the need for special clamp designs or clamps that can damage the finish. No weak bonds or gaps from wood movement - 300 elastic stretch. Sticks only to itself - no adhesive clean up. No tape adhesive to affect the wood or finish surface. Soft silicone is inert to most finishes. After the glue dries, simply cut the tape free.

Features:

• No weak bonds or gaps from wood movement
• 300 elastic stretch
• Sticks only to itself - no adhesive clean up
• Soft silicone is inert to most finishes.
• After the glue dries, simply cut the tape free.

Titewrap™

Titebond Titewrap eliminates the need for traditional clamps and secures your project while the glue dries! This self-adhering wrap sticks only to itself and won’t damage the wood surface. It is perfect for irregular joints or pieces that are difficult to clamp. When finished, simply cut the wrap away!

Features:

• 700 psi strength and 300% elastic stretch
• Self-bonding – Won’t damage wood surface
• Ideal for interior/exterior woodworking projects
• Eliminates need for traditional clamps
• Performs in high temperatures
• UL Listed for use at not more than 600 V and at not more than 80°C (176°F)
• Adheres only to itself Excellent moisture resistance
• Conforms to PROP 65