Bandsaw Accessories

Magfence II
Universal Magnetic Fence

The MAGFENCE II™ Universal Magnetic Fence is the fastest, easiest way to add a movable and adjustable fence to your bandsaw. Since the MAGFENCE II™ attaches to your saw with switchable magnets ( 155 lbs of break away force each), it is readily adjusted and infinitely positionable. You don't even need any hardware or mounts when installing. Simply place in position and switch the magnets to the ON position and you are set. The fence has thin rubber strips on the bottom to make adjustments smooth and simple, they also keep the fence from scratching your table top surface. The unit also features multiple T-slots for attaching any number of accessories like a sub-fence, stops and is compatible with all of Carter's original MAGFENCE™ accessories. The MAGFENCE II™ comes with two switchable magnets ( 155 lbs of break away force each) and measures 15" in length by 3" in height. Additional switchable magnets (sold separately) can be added to the fence for even more holding power

AccuRight Ratchet-Rod Tension Adjuster

The Ratchet-Rod Kit replaces the original threaded rod and nut of the bandsaw with an ACME-threaded rod and nut, for easy rotation, and includes a contoured ratcheting knob for quick and comfortable rotation. Inside the knob is a ratchet mechanism with a tiny flip lever that reverses the drive direction just like a socket wrench. Once the rod and nut are installed, tightening or loosening your blade is quick and easy. Even more ingenious, you can pop off the knob and snap on a 3/8” drive torque wrench to check your blade tension right off the torque wrench, which gives you repeatable blade tension results every time.

Clean Sweep

The Clean sweep™ helps keep your tires free from debris which shorten their life and effect blade tracking. As debris; saw dust, metal on metalworking saws, or any other debris accumulates on the tire, continued use without cleaning compresses the tire more in other places then if it were in contact with the rubber or urethane alone. Over time the tire will loose its rebound in those places if not cleaned properly and thus decrease tire life. (Currently only offered for 14" saws)

AccuRight® Zero Clearance Band Saw Insert

The Accu-Right® bandsaw zero clearance inserts reduce splintering and tea rout on your stock pieces. The inserts also prevent small pieces from falling down in between your blade and the lower wheel. The Accu-Right® inserts are designed to replace your old worn out stock insert. Perfect for scroll work, small delicate pieces, or woods that are prone to tearing out.

#3701 Band Saw Inserts Fit:

• Delta Band Saws

#3702 Band Saw Inserts Fit:

• Jet Band Saws

Cobra Coil™
Band Saw Tension Spring

Using large bandsaw blade sizes - is your bandsaw not performing up to standard or do you simply just want to tune your bandsaw up? Then the heavy duty Carter Cobra Coil™ Replacement Spring may be your answer. The Cobra Coil™ is a direct replacement for most 14” bandsaws tension spring. The Cobra Coil™ offers greater durability than the factory installed springs and the coils superior strength allows you to use larger (wider) bandsaw blades that require more tension that is not available with stock springs. The Cobra Coil™ will produce over 10,000 PSI of blade tension even on machines equipped with riser blocks. It is simple to install and it fits 14” Jet, 14” Delta, 14” General, 14” Ridgid, 14” Reliant, 14” Grizzly, 14” Powermatic, 14” Sears Contractor and the Cobra Coil™ fits most import 14” blade tensioning devices.

F.A.S.T Fence Alignment System Tool
5 Setup Bars

F.A.S.T
The F.A.S.T is a new take on an old idea. Designed to give you a quick pre set height or thickness gauge for all of your projects. We added a ruler on the front and a rare earth magnet on the back to hold the F.A.S.T in place during set up. The F.A.S.T is made from aluminum and will not damage the teeth of your table saw, bandsaw blade or router bits.

Includes:

• 1/8" F.A.S.T Setup Bar
• 3/16" F.A.S.T Setup Bar
• 1/4" F.A.S.T Setup Bar
• 3/8" F.A.S.T Setup Bar
• 1/2" F.A.S.T Setup Bar

Bandsaw Fence Alignment
For checking alignment, place any F.A.S.T on your band saw blade with the teeth of the blade in the machined groove against the rare earth magnet and adjust your fence so it lines up parallel to the F.A.S.T Bar.

Bandsaw Cut Width
To set for cut width, choose the bar that corresponds to your desired cut width and place on the blade as mentioned above. Gently slide your fence against F.A.S.T Bar and lock your fence in place then remove the F.A.S.T and make the cut

Also Works with Router Tables, Table Saw and More
Place a F.A.S.T Bar that corresponds to your desired height for setting up your cutters. Simply raise or lower your cutter until it is flush with the top of the F.A.S.T Bar. Works great for a F.A.S.T setting between your table saw fence and blade as well.