Glue

×

Savers

Glue ups can be challenging enough so as it is, getting glue on the clamp bars or pipes makes it even more so. If there were something you could use to protect your bar clamps wouldn’t you want to use it? Well, the SILI™ Saver does just that! Simply take a SILI™ Saver protector and slip it on to your clamp bar or pipe and it will stay exactly where you put it. Not only does the SILI™ Saver protect your clamp bar or pipe, it won’t marr or damage the wood. With it’s unique design, the SILI™ Saver will fit on most bar clamps or pipe clamps. As with the entire "SILI™" product line, wood glue either washes off with warm water or you can simply let the glue dry and peel it right off of the SILI™ Saver protector.

×

Extendable Heavy Duty Press Roller

The Extendable Heavy Duty Segmented Roller provides excellent leverage while applying pressure to linoleum, carpets, tile, wall coverings, laminates, large veneer projects and more! Projects that were once difficult are now a cinch with this rugged tool with its ergonomic, heavy duty leverage handle and rubber rollers. The heavy duty cast leverage handle allows you lean into to apply as much pressure as needed and will take virtually all of your weight behind it. This helps you press and roll out your material as efficiently and as quickly as possible. Perfect for flooring projects

7-1/2" Wide 3 Roller Design

The 3 roller design helps evenly distribute pressure on to your work surface.Rollers that have one roller tend to place pressure on one side or the other which produces uneven and inconsistent results. With this heavy duty 3 roller tool, you'll be able to apply evenly distributed pressure on you projects and produce wonderful looking results! Each roller is approx. 1-1/2" in diameter and 2-7/32" long for a total width of 7-1/2" providing you with plenty of even pressure when in use.

The Long and Short of it...

Depending on the size of your project or if you need more leverage, you may want to lengthen or shorten the handle. The handle on the HD roller can be adjusted from 17-1/2" all the way up to 27" in length which is perfect for many floor installation projects. When working on bench tops or counter tops, it will probably be better to shorten the handle length to achieve better leverage. Either way, this HD roller tool has got you covered!

Evenly, Directly Distributed Pressusre

We designed the 3 rollers to be set in a segmented fashion so the pressure action of the rollers will be evenly and directly distributed behind each roller producing excellent results when pressure is applied. Some press rollers use a single roller type of tool which tends to produce inconsistent and uneven results.

Solid Non Marring Rubber Material

Each of the segmented rollers are made of a solid non marring rubber material so your work surface is safe from being marked or damaged when using it. Each roller is approx. 1-1/2" in diameter and 2-7/32" long for a total of 7-1/2" wide rolling surface.

×

Laminate J Roller

Applying veneer, laminate or even wall coverings usually requires some tools that you may not find in your neighborhood big box store or even at a local mom and pop hardware store. The Fulton J-Roller is one of those items and is the ideal tool for applying pressure to your sheet or paper goods to ensure proper adhesion to your work surface.

When applying veneer on wood for example, you generally need to exert a good amount of even downward pressure on the veneer sheet or roll. To do this, we could use a flat bar of some sort, but that generally won't be even enough and can't get into the slight undulations of the wood surface. The Fulton J-Roller is the perfect width to properly work the veneer for proper adhesion.

A full 12" long, the J-Roller is the perfect length to handle most any project where you need to apply sheet goods to another surface. The roller is made from a firm, non-marring, textured rubber material that helps you apply pressure where it is needed. The roller wall is about 3/8" thick so it will stand up to the rigorous chore of applying pressure to your sheet goods.

Apply pressure where its needed...

While there are a lot of rollers to choose from and many have larger (wider) rollers, the Fulton J-Roller was designed so it can work small or larger projects. Sometimes, when using larger wheels or 3 wheel rollers, those tend to not hit all the undulations properly leaving a very uneven or wavy appearance to the finished product. The Fulton J-Roller allows yo to place the pressure exactly where you need it to make sure you hit every last spot on your work surface for a wonderful looking project.

The ideal roller for veneer, laminate and even wall coverings

When you need to work your veneer, laminate or wall coverings on to your work surface, you'll need a roller of some sort to help with the task. The Fulton J-Roller was literally built for the job and can handle most any size project you throw at it!

Thick Walled, Heavy Duty Roller

To be honest, we are fairly certain that you will wear out long before the roller on this tool does. The 3/8" wall rubber roller is perfect for extended work sessions and it won't mar you work surface. The roller won't lose its shape over time and can be used over and over again without worrying about how long it will last.

Round Steel Handle with J-Hook

Built to withstand heavy pressure from rolling veneer, thick paper or laminate goods at a multitude of angles, the Fulton J-Roller is the perfect solution for gaining maximum adhesion.

The heavy duty steel handle is designed to help you exert as much pressure as possible to the work surface. The handle is wrapped with two separate sections of comfortable rubber grips for extended use and less hand fatigue. The bottom of the handle forms the "J" to attach the heavy duty rubber roller without getting in the way of your rolling process.

Using the Fulton J-Roller gives you the ability to evenly apply pressure to your veneer, laminates and wall coverings to provide maximum adhesion. Perfect for working many of those project types around the house or in your woodworking shop. The roller measures approximately 2-7/8" wide.

×

Veneer Scraper

If you have ever applied veneer to any type of substrate material then you probably know that rollers work pretty well but leave air pockets or bubbles behind almost every time. That’s where the Fulton Veneer Scraper steps in. With its beveled edges and long hardwood handle, you’ll be able to work out every last air pocket or bubble all the while gaining maximum adhesion to your substrate!

The Fulton Veneer Scraper is designed to be used on veneer when it is bonded to a substrate using contact cement or PSA backed veneers. The basic idea with this simple but very useful and effective tool is that all of the leverage of your arm and hand force is concentrated at the tip of the tool. This focuses all the pressure to the veneer and allows you to gain excellent adhesion.

The hardwood handle is approximately 11” long and approximately 5/8” thick. We have shaped the handle so its comfortably curved to fit into the palm of your hand. This makes it easy to grip and wont dig or tear into your hand while applying heavy pressure. The thick hardwood stands up to repeated, heavy pressure scrapes on project after project after project.

Apply pressure where its needed...

The scraper is made from a very rigid plastic material that doesn’t flex or give. This along with the beveled edges allows you to focus heavy pressure as needed on your veneer.

Smooth Beveled Edges

The business end of the scraper has beveled edges so the scraper doesn't dig into or tear at your wood veneer sheets when applying pressure. The Scraper is ready to go right out of the package with no need to de-burr the edges.

Thick Comfortable Grip Hardwood Handle

The 5/8" thick handle is not only comfortable to grip and use, its also very rigid and sturdy. It will stand up to repeated and prolonged use for years of workshop service.

Just the right size

The scraper and the handle together were designed to provide the right amount of leverage to be able to achieve the best bond possible between your veneer and substrate. The scraper measures approximately 3-11/16” wide by 2-1/16” tall and is secured to the handle using connector bolts. These bolts can be removed if you need to repair or replace the scraper.

Drag Outward From the Center

Simply angle the scraper and pull or drag the scraper from the center of your project outward toward the edge. This will pull all of the imperfections (bubbles/air pockets) to the edge of your substrate

Start at Number 1

Starting in the center of your project (1) and working your way outward in sequential order will help you cover your entire workpiece. Always remember to go with the grain of your veneer when applying pressure with the veneer scraper. Going against or across the grain will likely damage your veneer.