Table Saws & Accessories
Fence Clamps
|
||||||||||||||||
|
The Fulton Aluminum Universal Fence Clamps are the perfect solution for clamping auxiliary fences, stop blocks, setup blocks, corner clamps and more to vertical flat surfaces like fences without the clamps getting in the way. The clamp post arm fits into a 3/8" hole and is at a slight inward angle to keep the lower part of your fence or block up against a flat surface. Fitting into a hole on the top of the fence or block keeps the clamp completely out of the way unlike F-clamps or C-Clamps. The versatility of these clamps allows you to use them in most any way imaginable to make your work flow quicker and easier.
|
|||||||||||||||
California Residents:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||
|
||||||||||||||||
|
||||||||||||||||
|
MATCHFIT Dovetail Clamps by MICROJIG will revolutionize the way you work with wood. MATCHFIT Dovetail Clamps move through the grooves below the material, allowing you to clamp anywhere, on any surface, without being confined to the edge. Features new rubberized soft-grip handle for better hold when clamping your next project, and expands creative freedom to build extension fences, tables, workspaces, and personalized track systems.
|
|||||||||||||||
California Residents:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||
|
||||||||||||||||
|
||||||||||||||||
|
MATCHFIT Dovetail Clamps by MICROJIG will revolutionize the way you work with wood. MATCHFIT Dovetail Clamps move through the grooves below the material, allowing you to clamp anywhere, on any surface, without being confined to the edge. Features new rubberized soft-grip handle for better hold when clamping your next project, and expands creative freedom to build extension fences, tables, workspaces, and personalized track systems.
|
|||||||||||||||
California Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||
|
||||||||||||||||
|
||||||||||||||||
|
Create jigs and shop fixtures with the incredibly versatile MATCHFIT System. Dovetail Clamps and Dovetail Hardware move through the tracks below the surface, allowing you to create a variety of jigs that move freely, and tighten down anywhere you can route a groove. Create your own fences, stops, hold-downs, and assembly fixtures in a snap. The X-PAD is an upgrade for MATCHFIT Dovetail Clamps that allows you to clamp in two directions at once—achieving in-line clamping with unrestricted clamp positioning. Use the v-groove to clamp round stock with incredible ease. Compatible with the MATCHFIT Dovetail router bit, available in ½", 8mm, and 12mm shanks.
Includes:
|
|||||||||||||||
California Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||
|
||||||||||||||||
|
||||||||||||||||||||
|
Perfectly-fitted dados, joinery, and inlays without measuring, marking, or test cuts. It's simple, Using the legs as a stop, make your start and finish shoulder cuts. 1. Use Leg #1 to cut your first shoulder. Note: Microjig Matchfit Dovetail Clamp not included For use with MATCHFIT Dovetail Clamps |
|||||||||||||||||||
California Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||||||
|
||||||||||||||||||||
|
||||||||||||||||
|
The MATCHFIT Setup Gauge is used for setting up Microjigs® MATCHFIT Dado Stop. The Setup Gauge will allow you to setup for both the left and right side of your table saw blade kerf without having to set up the Matchfit Dado every single time. By Cutting the blade kerf into the gauge it eliminates the steps of having to set the kerfs thickness on the dado stop. The MATCHFIT Setup Gauge makes setting up the MATCHFIT Dado Stop:
Note: The Setup gauge is not required to use the MatchFit Dado Stop |
|||||||||||||||
California Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||
|
||||||||||||||||
|
||||||||||||||||||||
|
MICROJIG's exclusive MATCHFIT Dovetail Router Bit makes the MATCHFIT system faster and easier to use than ever before. The MATCHFIT Dovetail Router Bit is designed especially for the MATCHFIT Dovetail Clamps and dovetail hardware. Although it mills the same 14 degree, 1/2" profile as a standard dovetail bit, its unique design automatically rounds over the sharp top shoulders creating incredibly clean dovetail grooves and virtually eliminating the need for sanding. Experience the difference supreme engineering and attention to detail make.
Note: Gripper Not included |
|||||||||||||||||||
California Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||||||
|
||||||||||||||||||||
|
||||||||||||||||
|
Perfect with the Dovetail Router Bit. Specially designed to route 1/4" relief grooves in material prior to the MATCHFIT Dovetail Router Bit. The relief bit removes 55% of waste material, which reduces stress on your Dovetail Router Bit. This improves the quality of dovetail grooves and increases the overall lifespan of your MATCHFIT Dovetail Router Bit. Available in 1/2" and 1/4" shank sizes. How it works.
Specifications:
|
|||||||||||||||
California Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
||||||||||||||||
|
||||||||||||||||